10ge2p1x710-ethip4lispip6-ip4base-ndrpdr.robot revision ac89ba8a
1# Copyright (c) 2019 Cisco and/or its affiliates.
2# Licensed under the Apache License, Version 2.0 (the "License");
3# you may not use this file except in compliance with the License.
4# You may obtain a copy of the License at:
5#
6#     http://www.apache.org/licenses/LICENSE-2.0
7#
8# Unless required by applicable law or agreed to in writing, software
9# distributed under the License is distributed on an "AS IS" BASIS,
10# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
11# See the License for the specific language governing permissions and
12# limitations under the License.
13
14*** Settings ***
15| Resource | resources/libraries/robot/shared/default.robot
16| Resource | resources/libraries/robot/overlay/lisp_static_adjacency.robot
17| Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
18| ...
19| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
20| ... | NIC_Intel-X710 | IP4FWD | ENCAP | LISP | IP6UNRLAY | IP4OVRLAY
21| ... | DRV_VFIO_PCI
22| ...
23| Suite Setup | Setup suite single link | performance
24| Suite Teardown | Tear down suite | performance
25| Test Setup | Setup test
26| Test Teardown | Tear down test | performance
27| ...
28| Test Template | Local Template
29| ...
30| Documentation | *RFC2544: Pkt throughput Lisp test cases*
31| ...
32| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
33| ... | with single links between nodes.
34| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv6 on DUT1-DUT2,\
35| ... | Eth-IPv4 on TG-DUTn for IPv4 routing over LISPoIPv6 tunnel.
36| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
37| ... | routing and static routes. LISPoIPv6 tunnel is configured between DUT1\
38| ... | and DUT2. DUT1 and DUT2 tested with ${nic_name}.\
39| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
40| ... | Rate) with zero packet loss tolerance and throughput PDR (Partial Drop\
41| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
42| ... | of packets transmitted. NDR and PDR are discovered for different\
43| ... | Ethernet L2 frame sizes using MLRsearch library.\
44| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
45| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
46| ... | flow-group) with all packets containing Ethernet header, IPv4 header
47| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
48| ... | addresses of the TG node interfaces.
49| ... | *[Ref] Applicable standard specifications:* RFC6830.
50
51*** Variables ***
52| @{plugins_to_enable}= | dpdk_plugin.so
53| ${crypto_type}= | ${None}
54| ${nic_name}= | Intel-X710
55| ${nic_driver}= | vfio-pci
56| ${osi_layer}= | L3
57| ${overhead}= | ${48}
58# Traffic profile:
59| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src253
60
61*** Keywords ***
62| Local Template
63| | [Documentation]
64| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters\
65| | ... | config.
66| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
67| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
68| | ...
69| | ... | *Arguments:*
70| | ... | - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1).
71| | ... | Type: integer, string
72| | ... | - phy_cores - Number of physical cores. Type: integer
73| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
74| | ...
75| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None}
76| | ...
77| | Set Test Variable | \${frame_size}
78| | ...
79| | Given Set Max Rate And Jumbo
80| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq}
81| | And Pre-initialize layer driver | ${nic_driver}
82| | And Apply startup configuration on all VPP DUTs
83| | When Initialize layer driver | ${nic_driver}
84| | And Initialize layer interface
85| | And Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology
86| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
87| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
88| | And Configure LISP topology in 3-node circular topology
89| | ... | ${dut1} | ${dut1_if2} | ${NONE}
90| | ... | ${dut2} | ${dut2_if1} | ${NONE}
91| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
92| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
93| | Then Find NDR and PDR intervals using optimized search
94
95*** Test Cases ***
96| tc01-64B-1c-ethip4lispip6-ip4base-ndrpdr
97| | [Tags] | 64B | 1C
98| | frame_size=${64} | phy_cores=${1}
99
100| tc02-64B-2c-ethip4lispip6-ip4base-ndrpdr
101| | [Tags] | 64B | 2C
102| | frame_size=${64} | phy_cores=${2}
103
104| tc03-64B-4c-ethip4lispip6-ip4base-ndrpdr
105| | [Tags] | 64B | 4C
106| | frame_size=${64} | phy_cores=${4}
107
108| tc04-1518B-1c-ethip4lispip6-ip4base-ndrpdr
109| | [Tags] | 1518B | 1C
110| | frame_size=${1518} | phy_cores=${1}
111
112| tc05-1518B-2c-ethip4lispip6-ip4base-ndrpdr
113| | [Tags] | 1518B | 2C
114| | frame_size=${1518} | phy_cores=${2}
115
116| tc06-1518B-4c-ethip4lispip6-ip4base-ndrpdr
117| | [Tags] | 1518B | 4C
118| | frame_size=${1518} | phy_cores=${4}
119
120| tc07-9000B-1c-ethip4lispip6-ip4base-ndrpdr
121| | [Tags] | 9000B | 1C
122| | frame_size=${9000} | phy_cores=${1}
123
124| tc08-9000B-2c-ethip4lispip6-ip4base-ndrpdr
125| | [Tags] | 9000B | 2C
126| | frame_size=${9000} | phy_cores=${2}
127
128| tc09-9000B-4c-ethip4lispip6-ip4base-ndrpdr
129| | [Tags] | 9000B | 4C
130| | frame_size=${9000} | phy_cores=${4}
131
132| tc10-IMIX-1c-ethip4lispip6-ip4base-ndrpdr
133| | [Tags] | IMIX | 1C
134| | frame_size=IMIX_v4_1 | phy_cores=${1}
135
136| tc11-IMIX-2c-ethip4lispip6-ip4base-ndrpdr
137| | [Tags] | IMIX | 2C
138| | frame_size=IMIX_v4_1 | phy_cores=${2}
139
140| tc12-IMIX-4c-ethip4lispip6-ip4base-ndrpdr
141| | [Tags] | IMIX | 4C
142| | frame_size=IMIX_v4_1 | phy_cores=${4}
143